NCT02940782

Comparison Between Reciproc and Oneshape Systems

Assessment of Postoperative Pain After Using Reciroc Versus One Shape NiTi Systems in Patients With Symptomatic Irreversible Pulpitis (A Randomized Clinical Trial): Part Two

• Status: Unknown
• Phase: N/A
• Study type: Interventional
• Enrollment: 54 (estimated)
• Sponsor: Cairo University · Academic / Other
• Sex: All
• Age: 25 Years – 45 Years
• Healthy volunteers: Not accepted

Summary

A randomized clinical trial to assess postoperative pain in patients with symptomatic irreversible pulpitis after using Reciproc versus One Shape rotary NiTi Systems.

Detailed description

The study aims at comparing postoperative pain after using two single-file NiTi systems, Reciproc reciprocating system and One Shape rotary system, for root canal instrumentation in patients with symptomatic irreversible pulpitis. After the patient is found eligible, he/she will be randomly assigned to either the control (One Shape) or experimental group (Reciproc) and will be treated in a single visit. Sequence of Procedural Steps: 1. Assessment of preoperative pain by NRS before administration of anesthesia. 2. Administration of local anesthesia using 2% lidocaine (1:100,000 adrenaline). 3. An access cavity will be done using a round bur and Endo-Z bur. 4. Isolation of the affected tooth with rubber dam. 5. Determination of the working length using an electronic apex locator, and confirmed by a radiograph using K-file. Then, the working length will be established at 0.5 mm up to the radiographic apex. 6. Canals will be explored with hand K-file ISO sizes 10, 15, 20. 7. Mechanical preparation for both groups will be as follows: * Experimental group: * Canals will be instrumented using Reciproc reciprocating system set on an electric motor, with adjusted torque and speed according to the manufacturer's instructions. * There is no need for coronal preflaring with a Gates Glidden drill or an orifice opener since the design of the Reciproc instrument allows any obstructions in the coronal third to be removed, as claimed by the manufacturer. * Reciproc file selection: R40 (40/0.06) * Control group: * Coronal preflaring will be performed using Gates Glidden drill. * Canals will be instrumented using One Shape single-file (25/0.06) set on an electric motor with adjusted torque and speed according to the manufacturer's instructions. * For wide canals, One Shape Apical (30/0.06, 37/0.06) will be used. 8. The rotary files will be introduced inside the canal using EDTA gel. 9. Canals will be irrigated with 2.6% sodium hypochlorite solution between every subsequent instrument. It is prepared by adding 10 ml of sterile distilled water to 10 ml of 5.25% sodium hypochlorite solution using a 27 gauge needle fit to 5ml disposable plastic syringe placed in the canal space without binding. 10. Canals will be dried with sterile paper points and obturated using lateral condensation technique. A spreader will be used to allow space for auxiliary cones, with resin-based root canal sealer. 11. The tooth will be sealed by temporary restoration, and postoperative pain will be assessed immediately after the end of treatment. 12. The patient will be phone called for follow up after 6, 12, 24, 48 and 72 hours. 13. The patient will be instructed to return to complete the treatment procedures until placing a full-coverage restoration. 14. The patient will be instructed to take one tablet 600 mg Ibuprofen if he/she experiences severe pain.

Conditions

• Pulpitis

Interventions

Type	Name	Description
PROCEDURE	Reciproc single file system	A reciprocating Nickel Titanium single file system used for instrumentation of root canals in endodontic treatment.
PROCEDURE	One Shape single file system	A rotary Nickel Titanium single file system used for instrumentation of root canals in endodontic treatment.
DEVICE	X-smart Plus, Dentsply Maillefer, Ballaigues, Switzerland	It is a micro-motor designed for performing root canal treatments with the reciprocating, single file technique or traditional continuous rotation file system.

Timeline

• Start date: 2017-01-01
• Primary completion: 2017-10-01
• Completion: 2017-12-01
• First posted: 2016-10-21
• Last updated: 2016-10-21