NCT05510206

SmartArch vs Super Elastic NiTi Aligning Archwires

The Effectiveness of SmartArch Versus Super Elastic Nickel-titanium Aligning Archwires: a Randomized Clinical Trial

• Status: Completed
• Phase: N/A
• Study type: Interventional
• Enrollment: 40 (actual)
• Sponsor: University of Baghdad · Academic / Other
• Sex: All
• Age: 12 Years
• Healthy volunteers: Not accepted

Summary

This study is intended primarily to compare the alignment efficiency and rate of two different types of archwires that are used in the first stage of orthodontic treatment , also addressing pain and root resorption that may be associated during treatment, with the hypothesis being a consideration of no deference between the two archwires.

Detailed description

This will be a multicenter non-stratified prospective randomized clinical trial with parallel groups trial with equal randomization (1:1 allocation ratio), two public orthodontic center will allocate patients for this trial. The patients will be initially assessed for eligibility to be included in the study by the investigator. Those who will meet the inclusion criteria will be informed about the nature of the study verbally to take the initial approval for participation. Then they will be provided by the patient information sheet and consent form, which explains the nature of the study, to read carefully at home and provide their decision about participation at the subsequent appointment. If the patient age below 18 years, parent assent should be taken. Any further enquiries regarding the study by the patient should be resolved by the investigator on the second visit. The patients will be treated with straight wire appliance using MBT prescription brackets with 0.022-inch slot (Pinnacle®, Ortho Technology, USA). Bracket placement will be standardized using a height gauge. Initially, teeth polishing will be performed with pumice and rubber cup for 10 seconds using a low-speed handpiece, followed by water rinsing and air drying (oil-free air spray for 30 seconds). Bonding technique will be standardized as follows: * Teeth etching with 37% phosphoric acid gel for 30 seconds. * Rinsing thoroughly (5 seconds per tooth for liquid etchant and 10 seconds per tooth for gel etchant) to stop the etching process and to remove demineralized particles then air drying until the white frosty appearance of the etched surface is observed. * Application of a thin layer of Light Bond™ Sealant (Reliance®, Itasca, USA) for one minute and air application for 5 seconds. * Bonding of brackets and tubes using Light Bond™ light cure orthodontic adhesive (Reliance®, Itasca, USA) applied on their bases and light-cured above interproximal contacts at a distance of 2-3 mm (5 seconds mesially and 5 seconds distally for brackets and 10 seconds mesially and 10 seconds occlusally for molar tubes). All the participants will receive a standardized treatment protocol. At the day of bonding, 0.016-inch archwire will be placed for the Smartarch group. It will be re-ligated every four weeks. While, for the super elastic NiTi group, 0.014-inch archwire will be placed at the day of bonding and eight weeks later it will be replaced by the 0.018-inch archwire for another eight weeks. Archwires will be tied to the bracket by elastomeric modules, with laceback of canines to first molars. If there is any debonding during treatment, this should be dealt with as an emergency case and re-bonded within 24 hours, otherwise the case will be considered as dropout. Since this study will be performed during the initial phase of treatment, no deviation in the protocol of treatment will be accepted (such as adding additional archwire in the sequence or using power chain). A good-quality alginate impression for the lower arch should be taken pre-treatment and after 4, 8, 12 and 16 weeks and a stone study model is obtained. Periapical X-ray for the mandibular central incisors will be taken pre-treatment and after 16 weeks. The participants will be provided by a visual analog scale (0-10) to record their pain perception during the first week after each wire placement.

Conditions

• Crowding of Anterior Mandibular Teeth

Interventions

Type	Name	Description
DEVICE	Leveling and alignment	Polishing, Bonding of appliance, placement of the first arch wire for Super elastic NiTi group then the second wire after two months taking study model each month during the study For Smartarch Group placing experimental arch wire for 4 months , taking impression each month. For both groups peri-apical X-Ray to lower anterior teeth is taken prior to treatment and 4 months later, also visual pain analogue scale is taken for 7 days after placing archwires

Timeline

• Start date: 2022-04-17
• Primary completion: 2022-08-24
• Completion: 2022-12-14
• First posted: 2022-08-22
• Last updated: 2023-05-11

Locations

1 site across 1 country: Iraq